临安东诚防腐设备有限公司主营:浙江玻璃钢储罐、浙江玻璃钢防腐、杭州玻璃钢反应釜、浙江废气吸收塔、浙江废气处理设备、玻璃钢搅拌罐价格!
服务热线:186 5810 1028

新闻资讯 / NEWS

网站首页 > 新闻资讯
  • 玻璃钢防腐施工的注意事项有哪些?
  • 本站编辑:临安东诚防腐设备有限公司发布日期:2018-05-08 13:14 浏览次数:

玻璃钢防腐www.hzdcff.com施工的施工效果,牵动着很多客户的心,毕竟客户是凭借效果说话的.要想防腐施工效果满意,在进行防腐施工时以下几点是我们要注意的地方:

The construction effect of glass steel corrosion protection www.hzdcff.com construction involves a lot of customer's heart, after all, the customer is speaking with the effect. To be satisfied with the effect of anticorrosion construction, the following points we should pay attention to in the course of anticorrosion construction are:

一、嵌刮腻子

First, inlay putty

基层表面或表面或层间凹凸陷不平整处,须用刮刀嵌刮腻子,予以填平,24h后再贴玻璃布.腻子不宜太厚,否则热处理时易出现龟裂.

The surface or surface or interlayer of the base is uneven and uneven. The putty must be put with a scraper, and then filled, then the glass cloth is attached to 24h. The putty should not be too thick. Otherwise, it is easy to crack during heat treatment.

二、粘贴玻璃布

Two. Paste glass cloth

玻璃布的粘接顺序一般应与与泛水方向相反,先沟道、墙裙、孔洞,后地面.其搭接应了顷物料流动方向,粘接宽度一般不于50mm,各层搭接缝应错开.铺贴时玻璃布不要拉得太紧,达到基本直度即可.

The bonding order of glass cloth should be opposite to the direction of water spreading, first ditch, skirt, hole, back ground. Its lap should be the direction of material flow, the width is not 50mm, the lap joints should be opened.

三、粘贴

Three. Paste

方法有间断法和连续法两种,应根据施工条件和要求选用.本工程施工面积大,便于流水作业,防污染的条件较好,采用连续法.

There are two kinds of methods: discontinuous method and continuous method, which should be selected according to construction conditions and requirements. The construction area of this project is large and convenient for flow operation. The condition of pollution prevention is better, and continuous method is adopted.

四、连续法

Four. Continuous method

用毛刷或滚筒醮上环氧树酯胶料纵横各刷遍后,随即贴接靠前层玻璃布,并用刮板或毛刷将玻璃布贴紧压实,或用滚筒反复滚压使其充分渗透粘贴,直到达到设计要求的厚度.玻璃布一般采用鱼鳞式搭接法,即铺连层时,上层每幅布应压住下层各幅布的半幅第三、四、五层时,每幅布应分别压往.

The first layer of glass cloth is attached to the first layer of glass cloth with the brush or the roller, then the glass cloth is attached to the first layer, and the glass cloth is pressed and compacted with the scraper or brush, or the roller is repeatedly rolled so that it is fully penetrated and sticked until the thickness of the design is reached. The glass cloth usually uses the fish scale lap method, that is, when the layer is connected, the upper layer of cloth should press. For each half of the third, fourth, fifth layers of the lower layer, each cloth should be pressed separately.